Oracle 23c: Managing Flashback Database Logs Outside the Fast Recovery Area
Overview: In previous Database releases, you could store flashback database logs only in the fast recovery area Oracle 23c Database introduces the ... Read More
Apprenez-en plus sur les raisons pour lesquelles Eclipsys a été certifié comme un excellent lieu de travail au Canada, les meilleurs lieux de travail en Ontario et en technologie, et a été nommé le meilleur employeur de PME au Canada pendant 3 ans !
En savoir plus !In this blog, we will demonstrate the steps to peer two VCNs in different regions through a DRG in the same tenancy. This is called a remote VCN peering.
The peering allows the VCNs’ resources to communicate using private IP addresses without routing the traffic over the internet or through your on-premises network.
A remote peering connection (RPC) is a component you create on the DRG attached to your VCN. The RPC’s job is to act as a connection point for a remotely peered VCN. A given DRG must have a separate RPC for each remote peering it establishes for the VCN.
At a high level, the networking service components required for this scenario include:
|
VCN1 |
VCN2 |
Region |
Toronto (ca-toronto-1 |
Ashburn (us-Ashburn-1) |
VCN Name |
TOR-VCN |
ASH-VCN |
Private Subnet CIDR |
10.0.1.0/24 |
172.0.1.0/24 |
DRG |
TOR-DRG |
ASH-DRG |
RPC |
TOR-RPC |
ASH-RPC |
Compute Instance |
TOR-VM (10.0.1.129) |
ASH-VM (172.0.1.132) |
Prerequisites:
– In the “Create VCN attachment” page, enter the attachment name (TOR-DRG-VCN) and select VCN1 (TOR-VCN), then click the “Create VCN attachment” button
– Repeat the same steps done above to attach TOR-VCN
– Go to the TOR-DRG detail page and click on the “Remote peering connection attachments” tab
– Click the “Create remote peering connection” button
– In the “Create remote peering connection” page, enter the connection name and select compartment
– Repeat the steps done above to create the Toronto region RPC
– Go to the TOR-DRG detail page and click on the “Remote peering connection attachments” tab
– View the details of TOR-RPC by clicking the name of the TOR-RPC connection in the “Remote Peering Connection” column
– In the connection details page, click the “Establish Connection” button, enter the connection name, and select compartment
– In the “Establish connection” page, select the “us-Ashburn-1” region and enter the OCID of Ashburn RPC (ASH-RPC) (the remote peering RPC). When The connection is established, the RPC’s state changes to PEERED
– Hence, ASH-RPC peering state changes to PEERED as well
– On the route table page, click the “Add Route Rules” button and enter below route rule information below.
Target Type |
Destination Type |
Destination CIDR Block |
Dynamic Routing Gateway |
CDIR Block |
172.0.1.64/24 (VCN2-private subnet CIDR) |
– Repeat the same steps done above to configure the route table for TOR-VCN’s private subnet
Use below rule information below.
Target Type |
Destination Type |
Destination CIDR Block |
Dynamic Routing Gateway |
CDIR Block |
10.0.1.0/24 (VCN1-private subnet CIDR) |
– On the Security List page, click the “Add Ingress Rules” button and enter below Ingress rule information
Source Type |
Source CIDR |
IP PROTOCOL |
CIDR |
172.0.1.0/24 (VCN2-private subnet CIDR) |
All Protocols |
– Repeat the same steps done above to add the Ingress rule for VCN1, but use the below Ingress rule
Source Type |
Source CIDR |
IP PROTOCOL |
CIDR |
10.0.1.64/24 (VCN1-private subnet CIDR) |
All Protocols |
– Use RSA private key, which was generated while creating ASH-VM, to ssh from TOR-VM to opc@ASH-VM.
Thanks for reading!
Overview: In previous Database releases, you could store flashback database logs only in the fast recovery area Oracle 23c Database introduces the ... Read More
Overview: Oracle 23c Database introduces a new feature to control whether a user or session is enabled for read-write operations, irrespective of the ... Read More